Huawei Ekit wall socket Access Point Ap160 (50086816) Original price was: ₦97,000.00.Current price is: ₦85,000.00.
Back to products
Huawei Ekit Layer 3 Managed Switch S310-24P4S (GE) (98012201) Original price was: ₦480,000.00.Current price is: ₦423,000.00.

Huawei Ekit Layer 3 Managed Switch S310-48P4S (GE) (98012384)

Original price was: ₦925,000.00.Current price is: ₦890,000.00.

Huawei S310-48P4S 98012384 Switch (48*10/100/1000BASE-T ports(380W PoE+), 4*GE SFP ports, built-in AC power)

0 People watching this product now!

Fast Shipping

Carrier information

Secure Shopping

You're in safe hands

online support

24/7 Support

Unlimited help desk

Description

Huawei S310-48P4S 98012384 Switch (48*10/100/1000BASE-T ports(380W PoE+), 4*GE SFP ports, built-in AC power)

S310-48P4S

 

Overview

Table 4-120 Basic information about the S310-48P4S

ItemDetails
DescriptionS310-48P4S (48*10/100/1000BASE-T ports(380W PoE+), 4*GE SFP ports, built-in AC power)
Part Number98012384
ModelS310-48P4S
First supported versionV600R023C00

Components

Figure 4-41 S310-48P4S appearance
1Forty-eight 10/100/1000BASE-T PoE+ ports2Four 1000BASE-X ports
3One console port4One MODE button
5One RST button

NOTICE:

To restore the factory settings and reset the device, hold down the button for at least 6 seconds.

To reset the device, press the button.

Resetting the device will cause service interruption. Exercise caution when you press the button.

6Ground screw

NOTE:

It is used with a ground cable.
7Jack for AC power cable locking strap

NOTE:

The AC power cable locking strap is not delivered with the switch.
8AC socket

NOTE:

It is used with an AC power cable.

Ports

Table 4-121 Ports on the S310-48P4S

PortConnector TypeDescriptionAvailable Components
10/100/1000BASE-T portRJ45A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s.Ethernet cable
1000BASE-X portSFPA 1000BASE-X port can send and receive data at 1000 Mbit/s.
Console portRJ45The console port is connected to a console for on-site configuration.Console cable

Indicators and Buttons

Figure 4-42 Indicators on the Switch

The S310-48P4X model is used as an example. Non-PoE models do not have PoE indicator and PoE mode.

Table 4-122 Description of indicators on the switch

No.IndicatorNameColorStatusDescription
1PWRPower module indicatorOffThe switch is powered off.
GreenSteady onThe power supply is normal.
2SYSSystem status indicatorOffThe system is not running.
GreenFast blinkingThe system is starting.
GreenSteady onDuring the system startup preparation phase, the SYS indicator is steady green, which lasts for a maximum of 30 seconds.
GreenSlow blinkingThe system is running normally.
RedSteady onThe system does not work normally after registration, or a fan alarm or a temperature alarm has been generated.
3MSTStack indicatorOff
  • If you are not changing the indicator mode (default): The switch is a standby or slave switch in a stack or the stacking function is not enabled on the switch.
  • If you are changing the indicator mode: The stack mode is not selected.
GreenSteady onThe stack mode is selected. The switch is a standby or slave switch in a stack, and the service port indicators show the stack ID of the switch.
GreenBlinking
  • If you are not changing the indicator mode (default): The switch is the master switch in a stack or a standalone switch with the stacking function enabled.
  • If you are changing the indicator mode: The stack mode is selected. The switch is the master switch in a stack or a standalone switch, and the service port indicators show the stack ID of the master switch. After 45 seconds, the service port indicators automatically restore to the status mode.
4PoEPoE indicatorOffThe PoE mode is not selected.
GreenSteady onThe PoE mode is selected, and service port indicators show the PoE status of each port.
5MODEMode switch button
  • When you press this button once, the service port indicators change to the stack mode and show the stack ID of the local switch.
  • When you press this button a second time, the service port indicators change to the PoE mode and show the PoE status of each service port.
  • When you press this button a third time, the service port indicators restore to the default mode and show the connection status and link activity of each service port.

If you do not press the MODE button within 45 seconds, the service port indicators restore to the default mode. In this case, the PoE indicator is off.

NOTE:

Hold down the mode switch button for 6s and release it to start the web initial login mode. Either of the following situations will occur:

  • If the switch has no configuration file, the system attempts to enter the web initial login mode.

    If the system enters the web initial login mode successfully, the MST mode indicator turn green and stay on for a maximum of 45 seconds.

  • If the login fails, check whether the device uses factory default settings.
6Electrical service port indicator (one indicator for each port)Arrowheads show the positions of ports. A down arrowhead indicates a port at the bottom, and an up arrowhead indicates a port at the top.Meanings of service port indicators vary in different modes. For details, see Table 4-123 and Table 4-124.

NOTE:

If a power failure occurs on a device’s PCB board, indicators of the last four GE or 10GE optical ports on the device’s front panel blink green cyclically at an interval of 1 second, with each indicator illuminating for 0.25 seconds.

 

7Optical service port indicator (two indicators for each port)Each optical port has two single-color indicators. The one on the left is the ACT indicator (yellow), and the one on the right is the LINK indicator (green).

Arrowheads show the positions of ports. A down arrowhead indicates a port at the bottom, and an up arrowhead indicates a port at the top.

8CLOUDCloud indicator

NOTE:

In versions earlier than V600R024C00, this indicator is reserved.

OffThe device is not in the cloud management state.
BlueFast blinkingThe device is connecting to the cloud.
BlueSlow blinkingThe device is in the cloud management state.
BlueSteady onThe network is connected, and the management VLAN of the device obtains an IP address.
Table 4-123 Description of service port indicators in different modes (one indicator for each port)

Display ModeColorStatusDescription
Default modeOffThe port is not connected or has been shut down.
GreenSteady onA link has been established on the port.
GreenBlinkingThe port is sending or receiving data.
MST stack modeOffPort indicators do not show the stack ID of the switch.
GreenSteady onThe switch is not the master switch in a stack.

If the indicator of a port is steady on, the number of this port is the stack ID of the switch.

GreenBlinkingThe switch is the master switch in a stack.

If the indicator of a port is blinking, the number of this port is the stack ID of the switch.

PoE modeOffThe port is not providing power to a powered device (PD).
GreenSteady onThe port is providing power to a PD.
GreenBlinkingThe power of the PD connected to the port exceeds the power capacity of the port or the power threshold configured on the port. Alternatively, the PD does not comply with IEEE standards.
Table 4-124 Description of service port indicators in different modes (two indicators for each port)

Display ModeColorStatusDescription
Default mode (LINK indicator)OffThe port is not connected or has been shut down.
GreenSteady onA link has been established on the port.
Default mode (ACT indicator)OffThe port is not connected or has been shut down, or no data is transmitted or received.
YellowBlinkingThe port is sending or receiving data.

Power Supply System

The switch has a built-in AC power module and does not support pluggable power modules. The built-in power module can provide 380 W PoE power, which ensures full PoE power on 24 ports in compliance with 802.3af or on 12 ports in compliance with 802.3at.

Heat Dissipation System

The switch has two built-in fans for forced air cooling. Air flows in from the left side, and exhausts from the right side.

When working properly at a normal temperature, the device meets the desktop-class noise requirements. However, the fan speed may be high and the noise may be loud during device startup.

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-125 Technical specifications of the S310-48P4S

ItemSpecification
Dimensions without packaging (H x W x D) [mm(in.)]Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 220.0 mm (1.72 in. x 17.4 in. x 8.66 in.)

Maximum dimensions (the depth is the distance from ports on the front panel to the parts protruding from the rear panel): 43.6 mm x 442.0 mm x 227.0 mm (1.72 in. x 17.4 in. x 8.94 in.)

Dimensions with packaging (H x W x D) [mm(in.)]90.0 mm x 550.0 mm x 360.0 mm (3.54 in. x 21.65 in. x 14.17 in.)
Chassis height [U]1 U
Chassis materialMetal
Weight without packaging [kg(lb)]3.24 kg (7.14 lb)
Weight with packaging [kg(lb)]4.29 kg (9.46 lb)
Typical power consumption [W]48.64 W
Typical heat dissipation [BTU/hour]165.96 BTU/hour
Maximum power consumption [W]
  • Without PoE: 63.7 W
  • Full PoE load: 462.80 W (PoE: 380 W)
Maximum heat dissipation [BTU/hour]
  • Without PoE: 217.34
  • Full PoE load: 1579.12
Static power consumption34.04
MTBF [years]48.14 years
MTTR [hours]2 hours
Availability> 0.99999
Noise at normal temperature (acoustic power) [dB(A)]49.3 dB(A)
Noise at normal temperature (acoustic pressure) [dB(A)]37.3 dB(A)
Number of card slots0
Number of power slots0
Number of fans modules2
Switching capacityTo obtain data of this specification item, see the corresponding datasheet or contact the product sales personnel.
Packet forwarding rateTo obtain data of this specification item, see the corresponding datasheet or contact the product sales personnel.
Redundant power supplyNot supported
Long-term operating temperature [°C(°F)]-5°C to +50°C (23°F to 122°F) at an altitude of 0-1800 m (0-5905.44 ft.)
Restriction on the operating temperature variation rate [°C(°F)]When the altitude is 1800–5000 m (5906–16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).

Devices cannot start when the temperature is lower than 0°C (32°F).

The operating temperature ranges from –5°C (23°F) to +45°C (113°F) when optical modules with transmission distances greater than or equal to 60 km are used.

Storage temperature [°C(°F)]–40°C to +70°C (–40°F to +158°F)
Long-term operating relative humidity [RH]5% RH to 95% RH (non-condensing)
Long-term operating altitude [m(ft.)]0–5000 m (0–16404 ft.)
Storage altitude [m(ft.)]0-5000 m (0-16404 ft.)
Power supply modeAC built-in
Rated input voltage [V]
  • AC input: 100 V AC to 240 V AC, 50/60 Hz
  • High-voltage DC input: 240 V DC
Input voltage range [V]
  • AC input: 90 V AC to 290 V AC; 45 Hz to 65 Hz
  • High-voltage DC input: 190 V DC to 290 V DC
Maximum input current [A]6 A
Memory2 GB
Flash memoryPhysical space: 1 GB
Console portRJ45
Eth Management portNot supported
USBNot supported
RTCNot supported
RPS inputNot supported
Service port surge protection [kV]Common mode: ±7 kV
Power supply surge protection [kV]Differential mode: ±6 kV; common mode: ±6 kV
Ingress protection level (dustproof/waterproof)IP20
Types of fansBuilt-in
Heat dissipation modeAir cooling for heat dissipation, intelligent fan speed adjustment
Airflow directionAir intake from left and air exhaust from right
PoESupported
CertificationEMC certification

Safety certification

Manufacturing certification

Additional information
Brand

RELATED PRODUCTS